Husqvarna F2303Q0 Repair Manual Download Page 106

Page: 106 / 322

12 FUEL TANK, SEAT, TRIM

104

Main work

Check throttle cable routing. (

p. 48)

Position the fuel tank and fit the two spoilers laterally to the

radiator.

Make sure that no cables or throttle cables are trapped or

damaged.

- Attach the fuel tank breather hose to the fuel tank lid.
-

Mount and tighten screw

with the rubber bushing.

Guideline

Remaining screws,

chassis

Mount and tighten screws@.

Guideline

Remaining screws,

chassis

Plug in connector

for the fuel pump.

10 Nm (7.4 lbf ft)

Remove the wash cap set and thoroughly clean the plug-in

connection of the fuel line using compressed air.

Info

Under no circumstances should dirt enter into the fuel

line. Dirt in the fuel line clogs the injection valve!

Lubricate the 0-ring and connect plug-in connection

for

the fuel line.

Info

Route the cable and fuel line at a safe distance from

the exhaust system.

Finishing work

Mount the seat. (

p. 101)

Install the air filter box cover.

(

p. 96)

Install the right side cover. (

p. 100)

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands