Husqvarna F2303Q0 Repair Manual Download Page 265

Page: 265 / 322

CYLINDER HEAD 22

Engage the highest gear.

Turn the rear wheel until the engine is at ignition top dead
center.
✓ The markings

on the camshaft and screw G) on the

cylinder head are lined up.

Info

Make sure that the crankshaft is at top dead center.

Unscrew and remove screw

Remove washer

CD.

Mount and tighten screw

without the washer.

Check the valve clearance at all valves between the valve and
rocker arm.

Guideline

Valve clearance

Intake at: 20 °C (68 °F)

0.10 ... 0.15 mm (0.0039 ...
0.0059 in)

Exhaust at: 20 °C (68 °F) 0.12 ... 0.17 mm (0.0047 ...

0.0067 in)

Feeler gauge (590290411 00) (

p. 299)

If the valve clearance does not meet specifications:

- Adjust the valve clearance. (

p. 239)

Remove locking screw

Crank the engine several times.
Check the valve clearance and correct it if necessary.

Mount and tighten screw

with washer

CD.

Guideline

Screw plug, locking
screw

10 Nm (7.4 lbf ft)

263

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands