Husqvarna F2303Q0 Repair Manual Download Page 175

Page: 175 / 322

17.3

Engine disassembl

17.3.1

Preparations

17.3.2

Draining the engine oil

Install the right side cover. (

p. 100)

Mount the seat. (

p. 101)

Install the air filter box cover. (

p. 96)

Remove the motorcycle from the lift stand. (

p. 12)

Refill the coolant. (

p. 250)

Perform the initialization run. (

p. 268)

Go for a short test ride.

ENGINE 17

Read out the fault memory using the Husqvarna Motorcycles

diagnostics tool.

Check the engine for leak tightness.

Check the engine oil level. (

�

p. 252)

Check the coolant level. (

p. 249)

Mount the special tool on the engine assembly stand.

Holder and fitting for work stand (79429002000) (

p. 305)

Engine assembly stand (80329001 000) (

p. 306)

Mount the engine on the special tool.

Info

Work with an assistant or a motorized hoist.

Remove oil drain plug

with the magnet and seal ring.

Remove screw plug

Completely drain the engine oil.

173

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands