Husqvarna F2303Q0 Repair Manual Download Page 63

Page: 63 / 322

SHOCK ABSORBER, LINK FORK 9

- Position link fork and mount fork pivot.

Info

Pay attention to flat area

- Mount and tighten nut

Guideline

Nut, fork pivot

I M16x1 .5

I 100 Nm (73.8 lbf ft) I

- Mount the chain.

- Connect the chain with connecting link

@).

Guideline

The closed side of the chain joint lock must face in the

direction of travel.

- Position the foot brake cylinder.

✓ Push rod

engages in the foot brake cylinder.

•

Info

Ensure that the dust boot is correctly seated.

- Mount and tighten screws

Guideline

Remaining screws,

chassis

- Position the angle lever and linkage lever.

- Mount and tighten fitting (D.

Guideline

Nut, linkage lever to

M14x1 .5

angle lever

•

Info

Pay attention to flat area

- Mount and tighten screw @.

Guideline

10 Nm (7.4 lbf ft)

80 Nm (59 lbf ft)

Screw, bottom

M 1 0

shock absorber

60 Nm (44.3 lbf ft)

Loctite

2701

•

Info

Raise the wheel slightly to be able to mount the screw

more easily.

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands