Husqvarna F2303Q0 Repair Manual Download Page 257

Page: 257 / 322

401955-12

LUBRICATION SYSTEM 20

- Remove screws

Remove the oil filter cover with the O

ring.

- Pull oil filter (3 out of the oil filter housing.

Lock ring plier (51012011000) (

p. 297)

- Completely drain the engine oil.

- Thoroughly clean the parts and sealing surface.

- Lay the motorcycle on its side and fill the oil filter housing to

about ½ full with engine oil.

- Insert the oil filter into the oil filter housing.

- Lubricate the O-ring of the oil filter cover and mount it with

the oil filter cover

Mount and tighten the screws.

Guideline

Screw, oil filter cover

- Stand the motorcycle upright.

110 Nm (7.4 lbf ft)

- Remove filler plug

from the clutch cover together with the

O-ring, and fill up with engine oil.

Engine oil

•

Info

1.20 I

(1.27 qt.)

Engine oil

(SAE 1 0W/50)

(

p. 290)

Too little engine oil or poor-quality engine oil will result

in premature wear of the engine.

- Mount and tighten the filler plug together with the O-ring.

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

- Always make sure there is sufficient ventilation

when running the engine.

- Use effective exhaust extraction when starting or

running the engine in an enclosed space.

- Start the engine and check for tightness.

255

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands