Husqvarna F2303Q0 Repair Manual Download Page 23

Page: 23 / 322

6.13

FORK, TRIPLE CLAMP 6

Disassembling the fork legs

Caution

Danger of accidents

Disassembling pressurized parts can cause injuries.

- The fork is filled with compressed air. Please follow the description provided.

•

803522-10

803524-10

Condition

The fork legs have been removed.

Left fork leg

- Clamp the fork leg in the area of the lower triple clamp .

I Clamping stand (T1403S) (

!al

p. 310)

Release cartridge

using special tool

I Ring wrench (T14017) (

p. 310)

Info

The cartridge cannot be taken off yet.

- Unclamp the fork leg.

- Drain the fork oil.

- Clamp the fork leg with the axle clamp.

Guideline

I Use soft jaws.

Remove protection cap f).

- Remove screw

- Remove the cartridge.

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands