Husqvarna F2303Q0 Repair Manual Download Page 14

Page: 14 / 322

5 MOTORCYCLE

5.1

Raising the motorcycle with a lift stand

Note

Danger of damage

The parked vehicle can roll away or fall

over.

- Park the vehicle on a firm and level surface.

401942-01

- Raise the motorcycle at the frame underneath the engine.

I Lift stand (80329955100) (

p. 306)

✓ Neither wheel is in contact with the ground.

- Secure the motorcycle against falling

over.

5.2

Removing the motorcycle from the lift stand

Note

Material damage

The vehicle may be damaged by incorrect procedure when parking.

Significant damage may be caused if the vehicle rolls away or falls

over.

The components for parking the vehicle are designed only for the weight of the vehicle.

- Park the vehicle on a firm and level surface.

- Ensure that nobody sits on the vehicle when the vehicle is parked on a stand.

5.3

Note

402001-10

Starting the vehicle

Danger

- Remove the motorcycle from the lift stand.

- Remove the lift stand.

- To park the motorcycle, insert plug-in stand

into the left

side of the wheel spindle.

Info

Remove the plug-in stand before riding.

Danger of poisoning

death.

Exhaust gases are toxic and inhaling them may result in unconsciousness and

- Always make sure there is sufficient ventilation when running the engine.

- Use effective exhaust extraction when starting or running the engine in an enclosed space.

Engine damage

High revving speed with a cold engine negatively impacts the lifespan of the engine.

- Always run the engine warm at a low speed.

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands