Husqvarna F2303Q0 Repair Manual Download Page 211

Page: 211 / 322

302808-10

17.4.33 Checking the rocker arm shafts

306609-10

17.4.34 Installing the valves

.:;;,,

-8

310048-10

ENGINE 17

Check the sealing area of the cylinder for distortion using a

straight edge and the special tool.

Feeler gauge (59029041100) (

p. 299)

Cylinder/cylinder head -

sealing area distortion

:;; 0.10 mm (:;; 0.0039 in)

If the measured value does not meet specifications:

- Change the cylinder head.

Check sealing seat width

of the valves.

Valve

Intake sealing seat width 2.00 mm (0.0787 in)

Valve

Exhaust sealing seat

width

12.00 mm (0.0787 in)

If the measured value does not meet specifications:

Machine the valve seat.

Blow compressed air through all oil channels and check that

they are clear.

Check the rocker arm shafts for damage and wear.

If there is damage or wear:

- Change the rocker arm shafts.

Position valve spring seats

Mount the new valve stem

seals

Mount the valves according to their normal built-in position.
Mount the springs and spring retainers (D.

...

209

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands