Husqvarna F2303Q0 Repair Manual Download Page 241

Page: 241 / 322

ENGINE 17

Remove the special tool.

Locking screw (113080802) (

p. 295)

Mount and tighten screw @ with washer.

Guideline

Screw plug, locking
screw

10 Nm (7.4 lbf ft)

17.5.28 Adjusting the valve clearance

Main work

Remove the timing chain tensioner. (

p. 176)

Remove the camshaft. (

p. 177)

Raise the rocker arm

on the outside.

Remove shims @ and set them down according to the

installation position.

Correct the shims based on the results of the valve clearance

check.

Insert suitable shims.

Install the camshaft. (

p. 237)

Install the timing chain tensioner. (

p. 237)

Finishing work

Check the valve clearance. (

p. 238)

17 .5.29 Installing the alternator cover

Position alternator cover gasket

Position the alternator cover.
Mount screws @ with the washers, but do not tighten yet.

Guideline

Screw, alternator
cover

M6x25

10 Nm (7.4 lbf ft)

Mount screws

and tighten all screws in a crisscross pat

tern.

Guideline

Screw, alternator
cover

M6x25

10 Nm (7.4 lbf ft)

239

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands