Husqvarna F2303Q0 Repair Manual Download Page 92

Page: 92 / 322

9 SHOCK ABSORBER, LINK FORK

B04391-10

B04393-11

- Place special tool

underneath and press out heim

joint

using special tool

@).

I Pressing tool (T1207S) (

IOI

p. 309)

- Position the new heim joint

and the special tool.

Guideline

I Use soft jaws.

I Pressing tool (T1206)

(

p. 308)

- Press the heim joint all the way in.

- Press the heim joint against the lock ring using the special

tool.

I Pressing tool (T1207S) (

IOI

p. 309)

- Mount second lock ring

- Position both collar bushings

and press in.

Finishing work

- Install the shock absorber. (

p. 60)

- Check the free travel of the foot brake lever.

(

p. 152)

- Remove the motorcycle from the lift stand. (

IOI

p. 12)

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands