manualshive.com logo in svg

Huawei IAD108A, User Manual

The Huawei IAD108A is a versatile communication device that provides seamless connectivity. Unlock its full potential by accessing the user manual, available for free download at manualshive.com. This comprehensive manual offers valuable insights and step-by-step instructions to help you maximize the features and functionalities of your Huawei IAD108A.

Share
Download
background image

User Manual 
U-SYS IAD108 Integrated Access Device 

Chapter 5  Advanced 

Configuration 

 

5-13 

  vlan priority  : 7 

-------------------------------------------------- 

IAD2000(config)#tag vlanid 0 priority 3 

    Change the VLAN tag configuration will interrupt current 

convesations, conitnue?[Y|N]:y 

  Command executing, please wait... 

-------------------------------------------------- 

  vlan tag function is enable 

  vlan id        : 0 

  vlan priority  : 3 

-------------------------------------------------- 

IAD2000(config)# 

 

 

 

 

 

  Note: 

When the VLAN tag is used to separate voice and data packets, it must be ensured 
that the upper network equipment (a router or a LAN Switch) also supports VLAN tag. 
When the VLAN tag function is enabled, the current calls will be affected. 

 

Example:  

Set ToS (Type of Service) of the voice packets to the highest 

reliability, and that of the other packets to the lowest cost. 

IAD2000(config)#

tos voice priority reliability

 

  Command executing, please wait... 

-------------------------------------------------- 

  TOS of voice packets:  Maxmize reliability 

  TOS of other packets:  Normal service 

-------------------------------------------------- 

Summary of Contents for IAD108A








































































































































































































































































































Reviews:

No comments

Related manuals for IAD108A

Secure Computing NETWORK INTERFACE CARDS Manual preview
NETWORK INTERFACE CARDS
Brand: Secure Computing Pages: 17
Multitech MultiConnect Conduit Getting Started Manual preview
MultiConnect Conduit
Brand: Multitech Pages: 37
B meters RFM-C2 WMBUS User Manual preview
RFM-C2 WMBUS
Brand: B meters Pages: 29
QUNDIS Q node 5.5 Operating And Installation Instructions preview
Q node 5.5
Brand: QUNDIS Pages: 48
Lantronix G528 Quick Start Manual preview
G528
Brand: Lantronix Pages: 2
D-Link DI-707 Quick Installation Manual preview
DI-707
Brand: D-Link Pages: 7
D-Link DPG-2000W - AirPlus G Wireless Presentation Gateway Quick Installation Manual preview
DPG-2000W - AirPlus G Wireless Presentation Gateway
Brand: D-Link Pages: 12
D-Link DVG-2004S Quick User Manual preview
DVG-2004S
Brand: D-Link Pages: 37
D-Link DSA 5100 - Airspot - Gateway Installation Manual preview
DSA 5100 - Airspot - Gateway
Brand: D-Link Pages: 28
D-Link DIV-140 Quick Installation Manual preview
DIV-140
Brand: D-Link Pages: 12
D-Link DI-701 iShare Technical Manual preview
DI-701 iShare
Brand: D-Link Pages: 50
D-Link DSL-604+ User Manual preview
DSL-604+
Brand: D-Link Pages: 67
D-Link DHM-301T User Manual preview
DHM-301T
Brand: D-Link Pages: 17
D-Link DVG-2004S Quick Installation Manual preview
DVG-2004S
Brand: D-Link Pages: 13
D-Link DI-707 Specifications preview
DI-707
Brand: D-Link Pages: 2
D-Link DI-704 User Manual preview
DI-704
Brand: D-Link Pages: 37
D-Link DPN-124G Quick Installation Manual preview
DPN-124G
Brand: D-Link Pages: 42
D-Link DG-104SH Manual preview
DG-104SH
Brand: D-Link Pages: 83

Brands by name

Popular brands

Load more brands