Huawei IAD108A User Manual Download Page 135

Page: 135 / 295

User Manual
U-SYS IAD108 Integrated Access Device

Chapter 4 Configuring Data

4-59

6 0 6 Low No -

7 0 7 Low No -

------------------------------------------------------

IAD2000(config)#

For ordinary voice users, the above configurations can meet the

need and no more configurations are needed.

II.

Configuring SPC User Data

1) Add an internal SPC, which connects No.1 and No.3 ports

of IAD108, and its name is “iadspc”.

IAD2000(config)#

spc add start 1 end 3 name iadspc

Adding SPC succeeded! The SPC index is: 0.

IAD2000(config)#

After the internal SPC is successfully created, index “0” will be

returned.

2) Add an IP SPC.

IP address of IAD108A is 10.70.33.62.

IP address of IAD108B is 10.70.10.26.

This IP SPC is established between No.6 port of IAD108
and No.1 port of IAD108B.

RTP port number of IAD108A is 50000.

RTP port number of IAD108B is 50004.

The name of the SPC is “ipspc”.

Summary of Contents for IAD108A








































































































































































































































































































Search results

Summary of Contents for IAD108A

Reviews:

Huawei IAD108A, User Manual, Page: 135 / 295

Search results

Summary of Contents for IAD108A

Reviews: