Huawei IAD108A User Manual Download

Page: 284 / 295

User Manual
U-SYS IAD108 Integrated Access Device

Appendix A Command List

A-8

Command name

Function

Mode

no terminal hold

Unlocking the terminal.

User

no terminal timeout

Disabling the function that when
the terminal timeouts it exits from
the system.

User

no timeout

Closing the terminal timeout
control switch.

User

no trunk enable

Deactivating a TRUNK group.

LAN Switch

no trunk group

Deleting the LAN Switch interface
of a TRUNK group.

LAN Switch

no uplink

Configuring a network interface
as non-uplink interface.

LAN Switch

no user apdinfo

Deleting the user’s appendix
information.

Global Config

no user name

Deleting a user.

Global Config

no vlan

Deleting all the ports in a VLAN. LAN Switch

patch active

Activating a patch.

Privilege

patch remove

Deleting a patch.

Privilege

patch start

Running the patch normally, after

rebooting it can run normally.

Privilege

ping

Checking the network connection

or whether the host is reachable. User

priority

Configuring a network interface

as with high priority.

LAN Switch

pstnport attribute set

Setting the PSTN interface

attribute

Global Config

Summary of Contents for IAD108A








































































































































































































































































































Search results

Summary of Contents for IAD108A

Reviews:

Related manuals for IAD108A

Brands by name

Popular brands

Huawei IAD108A, User Manual

Search results

Summary of Contents for IAD108A

Reviews:

Related manuals for IAD108A

Brands by name

Popular brands