Huawei IAD108A User Manual Download

Page: 162 / 295

User Manual
U-SYS IAD108 Integrated Access Device

Chapter 5 Advanced

Configuration

5-25

mgcip2:1.1.1.1 mgcport2:2222

mgc-domain-name2:huawei1.com

IAD2000(config)#

Table 5-14 lists the commands used to configure backup MGC.

Table 5-14

Related commands

Operation Command

Turn on the switch for
configuring backup MGC

IAD2000(config)

mg software-parameter

name

value

Configure the standby MGC

IAD2000(config)

mg backup

{

mgcip

mgcip

mgcport

mgcport

mgc-domain-name

mgc-domain-name

}

Query MG software
parameter

IAD2000>

show mg software-parameterr

Display the MGC

IAD2000>

show mg mgc

Table 5-15 lists the parameters of the related commands and their

meanings

Table 5-15

Parameter description

Item Description

mgcip

The IP address or the domain name of the standby MGC. It must be
consistent with that actually configured to the standby MGC. The

domain name is a character string of 1–60 characters.

mgcport

The port number of transmission layer protocol. With MGCP, only text
coding is supported and the default port number is 2727.

Summary of Contents for IAD108A








































































































































































































































































































Search results

Summary of Contents for IAD108A

Reviews:

Related manuals for IAD108A

Brands by name

Popular brands

Huawei IAD108A, User Manual

Search results

Summary of Contents for IAD108A

Reviews:

Related manuals for IAD108A

Brands by name

Popular brands