HP Z400 - Workstation Page 17 Maintenance And Service Manual Download

Page: 17 / 254

Workstation components

This section describes workstation components, including front and rear panel components.

For complete and current information on supported accessories and components for the workstation,

see

http://partsurfer.hp.com

Chassis components

The following image shows the components of a typical workstation configuration. Drive configurations

can vary.

Figure 1-3

Workstation components

Table 1-1

Workstation component descriptions

Item

Description

Item

Description

Power supply

Memory module (DIMM)

Side access panel

System board

Rear system fan

PCIe card

SFF Hard drive

PCI card

Hard disk drive

Airflow guide (for 6-DIMM Z400 product)

Optical drive

Speaker

Processor (CPU) heatsink

Front bezel

Processor

Chassis

ENWW

Product features

Summary of Contents for Z400 - Workstation































































































































































































































































Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands

HP Z400 - Workstation, Maintenance And Service Manual

Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands