manualshive.com logo in svg

HP Z400 - Workstation, Maintenance And Service Manual

The HP Z400 Workstation is a professional-grade powerhouse designed for demanding tasks. Enhance your productivity with this high-performance device that combines speed and reliability. Find complete guidance in the Quick Reference Manual available for free download at manualshive.com. Unlock the full potential of your workstation with this comprehensive manual.

Share
Download
background image

BIOS ROM

The BIOS ROM is a collection of machine language applications stored as firmware in ROM. It includes

functions such as POST, PCI device initialization, Plug and Play support, power management, and the

Computer Setup (F10) Utility. The BIOS ROM is a 1-MB Serial Peripheral Interface (SPI) port.

See 

http://www.hp.com/go/quickspecs

 to review the latest BIOS ROM specifications.

The Computer Setup (F10) Utility

This section contains these topics:

Topics

Computer Setup (F10) functionality on page 31

Accessing the Computer Setup (F10) Utility on page 33

The Computer Setup (F10) Utility menu on page 34

Computer Setup (F10) functionality

The Computer Setup (F10) Utility lets you:

●

Change factory default settings and set or change the workstation configuration, which might be

necessary when you add or remove hardware.

●

Determine if all devices installed on the workstation are recognized by the system and functioning.

●

Determine information about the operating environment of the workstation.

●

Solve system configuration errors that are detected but not fixed during the Power-On Self-Test

(POST).

●

Establish and manage passwords and other security features.

●

Establish and manage energy-saving time-outs (not supported on Linux platforms).

●

Modify or restore factory default settings.

●

Set the workstation date and time.

●

Set, view, change, or verify the workstation configuration, including settings for CPU, graphics,

memory, audio, storage, communications, and input devices.

●

Modify the boot order of installed mass storage devices such as SATA, SAS, diskette drives,

optical disk drives, network drives, LS-120 drives and USB boot devices.

●

Configure the boot priority of SATA and SAS hard-drive controllers.

●

Enable or disable Network Server Mode, which lets the workstation start the operating system

when the power-on password is enabled with or without a keyboard or mouse attached. When

attached to the workstation, the keyboard and mouse remain locked until the power-on password

is entered.

●

Enable or disable POST Messages to change the display status of POST messages. POST

Messages disabled suppresses most POST messages, such as memory count, product name, and

ENWW

BIOS ROM

31

Summary of Contents for Z400 - Workstation































































































































































































































































Reviews:

No comments

Related manuals for Z400 - Workstation

Eclipse E-iSERV CD7200 mkII Owner'S Manual preview
E-iSERV CD7200 mkII
Brand: Eclipse Pages: 119
Eclipse AVN726E Owner'S Manual preview
AVN726E
Brand: Eclipse Pages: 230
Eclipse CD5000 - ECLIPSE - Radio Installation Manual preview
CD5000 - ECLIPSE - Radio
Brand: Eclipse Pages: 40
Eclipse avn5435 Installation Manual preview
avn5435
Brand: Eclipse Pages: 20
Eclipse AVN2454 Owner'S Manual preview
AVN2454
Brand: Eclipse Pages: 98
Datalogic QuickScan QM2430-BK-433K2 Quick Reference Manual preview
QuickScan QM2430-BK-433K2
Brand: Datalogic Pages: 40
Jensen VM9411 Instruction Manual preview
VM9411
Brand: Jensen Pages: 110
Boss Audio Systems BV9955 User Manual preview
BV9955
Brand: Boss Audio Systems Pages: 18
Skoda Radio Funky Operating Instructions Manual preview
Radio Funky
Brand: Skoda Pages: 13
Alpha WMP-ND03B User Manual preview
WMP-ND03B
Brand: Alpha Pages: 17
Axxera AV615BHM Installation & Owner'S Manual preview
AV615BHM
Brand: Axxera Pages: 31
Alien Skylark WMU2000 User Manual preview
Skylark WMU2000
Brand: Alien Pages: 28
Duali DE-930 User Manual preview
DE-930
Brand: Duali Pages: 12
Vantec UGT-ST310R User Manual preview
UGT-ST310R
Brand: Vantec Pages: 20
Franklin BOOKMAN BPS-840 User Manual preview
BOOKMAN BPS-840
Brand: Franklin Pages: 42
Narvitech NV100C Quick Start Manual preview
NV100C
Brand: Narvitech Pages: 16
Renesas Tsi301 HyperTransport User Manual preview
Tsi301 HyperTransport
Brand: Renesas Pages: 80
StarTech.com PCIPOST Instruction Manual preview
PCIPOST
Brand: StarTech.com Pages: 26

Brands by name

Popular brands

Load more brands