manualshive.com logo in svg

HP Z400 - Workstation, Maintenance And Service Manual

The HP Z400 Workstation is a professional-grade powerhouse designed for demanding tasks. Enhance your productivity with this high-performance device that combines speed and reliability. Find complete guidance in the Quick Reference Manual available for free download at manualshive.com. Unlock the full potential of your workstation with this comprehensive manual.

Share
Download
background image

Configuring system BIOS

Configure the system BIOS to enable embedded SATA RAID functionality.

1.

To enter the system BIOS setup, press 

F10

.

2.

Use the arrow keys to highlight the desired language, and then press 

Enter

.

3.

Use the arrows to highlight 

Storage>Storage Options

, and then press 

Enter

.

4.

Use the up or down arrow key to highlight 

SATA Emulation

.

5.

Use the left or right arrow key to select 

RAID+AHCI

.

6.

To accept the new setting, press 

F10

.

7.

Use the arrows to highlight 

Advanced>Power-On Options

, and then press 

Enter

.

8.

Use the up or down arrow key to highlight 

POST Messages

.

9.

Use the left or right arrow key to select 

Enable

.

10.

To accept the new setting, press 

F10

.

11.

Use the arrow keys to highlight 

Advanced>Device Options

, and then press 

Enter

.

12.

Use the up or down arrow key to highlight 

SATA RAID Option ROM Download

, and then

press 

Enter

.

13.

Use the left or right arrow key to select 

Enable

.

14.

To accept the new setting, press 

F10

.

15.

Use the arrows to highlight 

File>Save Changes and Exit

, and then press 

Enter

.

16.

Press 

F10

 when prompted.

ENWW

Configuring SATA RAID devices

209

Summary of Contents for Z400 - Workstation































































































































































































































































Reviews:

No comments

Related manuals for Z400 - Workstation

EarthWay 2170 Assembly Instructions Manual preview
2170
Brand: EarthWay Pages: 12
Davis Instruments 8105 User Manual preview
8105
Brand: Davis Instruments Pages: 16
Jamex 8220 User Manual preview
8220
Brand: Jamex Pages: 10
Majestic SD 236BT/RDS/USB/AX Instruction Manual preview
SD 236BT/RDS/USB/AX
Brand: Majestic Pages: 6
Fametech BT-650-C User Manual preview
BT-650-C
Brand: Fametech Pages: 40
Handpoint SmartPOS PAX A80 User Manual preview
SmartPOS PAX A80
Brand: Handpoint Pages: 6
U-Line H-2813 Quick Manual preview
H-2813
Brand: U-Line Pages: 3
3Com ATMLINK 155 PCI User Manual preview
ATMLINK 155 PCI
Brand: 3Com Pages: 130
SaltDogg TGS06 Installation Instructions Manual preview
TGS06
Brand: SaltDogg Pages: 8
Yarvik EBR070 GoBook Start Manual preview
EBR070 GoBook
Brand: Yarvik Pages: 20
Magtek cDynamo Quick Installation Manual preview
cDynamo
Brand: Magtek Pages: 2
Danpex ADP1100 User Manual preview
ADP1100
Brand: Danpex Pages: 3
Boss Audio Systems BV9976B User Manual preview
BV9976B
Brand: Boss Audio Systems Pages: 36
Pyle PLR18MPF Manual preview
PLR18MPF
Brand: Pyle Pages: 4
Gandy 10T Series Operator'S Manual preview
10T Series
Brand: Gandy Pages: 10
Planet WNL-9320 User Manual preview
WNL-9320
Brand: Planet Pages: 41
Caliber RCD 236DAB-BT Manual preview
RCD 236DAB-BT
Brand: Caliber Pages: 18
Panasonic PP103914 Owner'S Manual preview
PP103914
Brand: Panasonic Pages: 5

Brands by name

Popular brands

Load more brands