manualshive.com logo in svg

HP Z400 - Workstation, Maintenance And Service Manual

The HP Z400 Workstation is a professional-grade powerhouse designed for demanding tasks. Enhance your productivity with this high-performance device that combines speed and reliability. Find complete guidance in the Quick Reference Manual available for free download at manualshive.com. Unlock the full potential of your workstation with this comprehensive manual.

Share
Download
background image

Setting up the Microsoft operating system

NOTE:

If you ordered a downgrade from Windows 7 or Windows Vista to Windows XP Professional

operating system, your system will be preinstalled with Windows XP Professional operating system.

With this configuration, you will receive recovery media for the Windows 7 or Windows Vista

operating system only. In case you need to restore or recover the Windows XP Professional operating

system in the future, it is important that you create recovery media disks for Windows XP Professional

operating system after first boot.

When you first apply power to the workstation, the operating system is installed. This process takes

approximately 5 to 10 minutes. Carefully follow the instructions on the screen to complete the

installation.

CAUTION:

After installation has started, do 

not

 turn off the workstation until the process is complete.

Turning off the workstation during installation can damage the installation and operation of the

software.

For complete operating system installation and configuration instructions, see the operating system

documentation that was provided with the workstation. Additional information is available in the online

help tool after you successfully install the operating system.

Installing or upgrading device drivers

To install hardware devices after the operating system is installed, you must install the appropriate

device drivers before you install the devices. Follow the installation instructions that came with the

device. In addition, for optimum performance, your operating system must have the most recent

updates, patches, and software fixes. For additional driver and software update information, refer to

Upgrading device drivers on page 23

.

Transferring files and settings to your Windows workstation

The Microsoft Windows operating system offers data migration tools that helps you choose and transfer

files and data from a Windows computer to your Windows 7, Windows Vista, or Windows XP

Professional operating system workstation.

For instructions on how to use these tools, see the documents at 

http://www.microsoft.com

.

ENWW

Setting up the Microsoft operating system

19

Summary of Contents for Z400 - Workstation































































































































































































































































Reviews:

No comments

Related manuals for Z400 - Workstation

Datalogic MAGELLAN 1400I Reference Manual preview
MAGELLAN 1400I
Brand: Datalogic Pages: 184
Datalogic Gryphon I GD4100 Quick Reference Manual preview
Gryphon I GD4100
Brand: Datalogic Pages: 28
Datalogic Magellan 2200VS Product Reference Manual preview
Magellan 2200VS
Brand: Datalogic Pages: 388
Datalogic Gryphon I GD44XX Product Reference Manual preview
Gryphon I GD44XX
Brand: Datalogic Pages: 324
Datalogic Gryphon GD4200 Product Reference Manual preview
Gryphon GD4200
Brand: Datalogic Pages: 304
Datalogic Gryphon 2D Series Reference Manual preview
Gryphon 2D Series
Brand: Datalogic Pages: 356
Datalogic Magellan 1100i Product Reference Manual preview
Magellan 1100i
Brand: Datalogic Pages: 208
Datalogic DX8200A Quick Manual preview
DX8200A
Brand: Datalogic Pages: 18
Datalogic DX6400 Quick Reference Manual preview
DX6400
Brand: Datalogic Pages: 16
Datalogic DS4600A Quick Reference Manual preview
DS4600A
Brand: Datalogic Pages: 12
Datalogic Dragon D151 Quick Reference Manual preview
Dragon D151
Brand: Datalogic Pages: 20
Datalogic DS1100 SH2347 Reference Manual preview
DS1100 SH2347
Brand: Datalogic Pages: 48
Datalogic Compact 2D Reader Matrix-2000 Quick Reference Manual preview
Compact 2D Reader Matrix-2000
Brand: Datalogic Pages: 11
Datalogic Lynx D Reference Manual preview
Lynx D
Brand: Datalogic Pages: 169
Datalogic Lynx D User Manual preview
Lynx D
Brand: Datalogic Pages: 72
Datalogic Gryphon GD4100 User Manual preview
Gryphon GD4100
Brand: Datalogic Pages: 10
Datalogic Gryphon I GD4100 Reference Manual preview
Gryphon I GD4100
Brand: Datalogic Pages: 428
Datalogic Magellan 800i Product Reference Manual preview
Magellan 800i
Brand: Datalogic Pages: 168

Brands by name

Popular brands

Load more brands