manualshive.com logo in svg

HP Z400 - Workstation, Maintenance And Service Manual

The HP Z400 Workstation is a professional-grade powerhouse designed for demanding tasks. Enhance your productivity with this high-performance device that combines speed and reliability. Find complete guidance in the Quick Reference Manual available for free download at manualshive.com. Unlock the full potential of your workstation with this comprehensive manual.

Share
Download
background image

Table 6-5

  Display problems (continued)

Problem

Cause

Solution

Dim characters

The brightness and contrast
controls are not set properly.

Adjust the monitor brightness and contrast controls.

Cables are not properly
connected.

Verify that the graphics cable is connected to the graphics
card and the monitor.

Blurry video or requested
resolution cannot be set.

If the graphics controller was
upgraded, the correct video
drivers might not be loaded.

Install the video drivers included in the upgrade kit, or
download and install the latest drivers for your graphics
card from 

http://welcome.hp.com/country/us/en/

support.html

.

Monitor cannot display
requested resolution.

Change the requested resolution.

The picture is broken up, rolls,
jitters, or flashes.

The monitor connections might
be faulty, or the monitor might
be incorrectly adjusted.

1.

Be sure the monitor cable is securely connected to the
workstation.

2.

In a multiple CRT monitor system, ensure that the
monitors' electromagnetic fields are not interfering
with each other . Move them apart if necessary.

3.

Move fluorescent lights or fans that are too close to
the CRT monitor.

Monitor must be degaussed.

Degauss the monitor.

Vibrating or rattling noise coming
from inside a CRT monitor when
powered on.

Monitor degaussing coil has
been activated.

None. It is normal for the degaussing coil to be activated
when the monitor is powered on.

Clicking noise coming from inside
a CRT monitor.

Electronic relays have been
activated inside the monitor.

None. It is normal for some monitors to make a clicking
noise when turned on and off, when going in and out of
Standby mode, and when changing resolutions.

High pitched noise coming from
inside a flat-panel monitor.

Brightness and contrast
settings are too high.

Lower brightness and contrast settings.

Fuzzy focus; streaking, ghosting,
or shadowing effects; horizontal
scrolling lines; faint vertical bars;
or unable to center the picture on
the screen (flat-panel monitors
using an analog VGA input
connection only.)

Flat-panel monitor’s internal
digital conversion circuits
might be unable to correctly
interpret the output
synchronization of the
graphics card.

1.

Select the monitor’s 

Auto-Adjustment

 option in the

monitor’s onscreen display menu.

2.

Manually synchronize the Clock and Clock Phase
onscreen display functions.

3.

Download SoftPaq SP22333 to assist with the
synchronization).

Some typed symbols do not
appear correctly.

The font you are using does
not support that symbol.

Use the Character Map to locate and select the
appropriate symbol.

Select 

Start>All Programs> Accessories>System

Tools>Character Map

. You can copy the symbol from

the Character Map into a document.

182

Chapter 6   Diagnostics and troubleshooting

ENWW

Summary of Contents for Z400 - Workstation































































































































































































































































Reviews:

No comments

Related manuals for Z400 - Workstation

EarthWay M30 Operation And Assembly Manual preview
M30
Brand: EarthWay Pages: 6
Douglas Dynamics SnowEx V-Pro SP-2000 Installation Instructions Manual preview
SnowEx V-Pro SP-2000
Brand: Douglas Dynamics Pages: 16
Eonon E646 Operating Instructions Manual preview
E646
Brand: Eonon Pages: 16
SnowEx V-Pro SP-2000 Owner'S Manual preview
V-Pro SP-2000
Brand: SnowEx Pages: 20
StarTech.com PEX1S1P952 User Manual preview
PEX1S1P952
Brand: StarTech.com Pages: 10
Stid SLA-R41-A-U04 Installation Procedures Manual preview
SLA-R41-A-U04
Brand: Stid Pages: 16
SnowEx SP-1075X Owner'S Manual And Installation Instructions preview
SP-1075X
Brand: SnowEx Pages: 24
Alpine IVA-D800R Owner'S Manual preview
IVA-D800R
Brand: Alpine Pages: 95
Pyramid CDR42DX Instruction Manual preview
CDR42DX
Brand: Pyramid Pages: 12
Sirius Satellite Radio STARMATE REPLAY ST2 User And Installation Manual preview
STARMATE REPLAY ST2
Brand: Sirius Satellite Radio Pages: 60
Boss Audio Systems 748UAI User Manual preview
748UAI
Brand: Boss Audio Systems Pages: 11
Datalogic Gryphon M 00 Series Quick Reference Manual preview
Gryphon M 00 Series
Brand: Datalogic Pages: 18
Caliber RCD264BT User Manual preview
RCD264BT
Brand: Caliber Pages: 20
Kenwood DDX6019 - DVD Player With LCD Monitor Installation Manual preview
DDX6019 - DVD Player With LCD Monitor
Brand: Kenwood Pages: 24
Kenwood DDX4038 Installation Manual preview
DDX4038
Brand: Kenwood Pages: 8
Kenwood DDX5022 Installation Manual preview
DDX5022
Brand: Kenwood Pages: 12
Kenwood DDX6029 Installation Manual preview
DDX6029
Brand: Kenwood Pages: 72
Kenwood DDX416BT Instruction Manual preview
DDX416BT
Brand: Kenwood Pages: 76

Brands by name

Popular brands

Load more brands