HP Z400 - Workstation Maintenance And Service Manual Download

Page: 210 / 254

Table 6-8

Diagnostic lights and audible codes (continued)

Activity

Possible cause

Recommended action

Red Power LED blinks seven
times, once every second,
followed by a two- second
pause. Seven beeps.

System board failure (ROM
detected failure prior to
video).

Clear CMOS.

NOTE:

Refer to the

Maintenance and Service Guide

for the

workstation model for detailed information on clearing CMOS.

The problem might be on the system board. Contact HP for
assistance.

Red Power LED blinks eight
times, once every second,
followed by a two-second
pause. Eight beeps.

Invalid ROM based on bad
checksum.

CAUTION:

Internal components might be powered even when the

workstation is off. To prevent damage, disconnect the workstation power
cord before you remove a component.

Clear CMOS.

NOTE:

Refer to the

Maintenance and Service Guide

for the

workstation model for detailed information on clearing CMOS.

Upgrade the ROM using SoftPaq from the hard disk drive, CD,
diskette, or USB removable device (for example, HP Drive Key). See
the ROM Flash section of the

Maintenance and Service Guide

http://www.hp.com/support/workstation_manuals

. SoftPaq is a

self-extracting executable that lets you upgrade the ROM. The
executable contains contains use instructions, To download
Softpaq, visit

http://www.hp.com/go/workstationsupport

The system board might have a problem. Contact HP for assistance.

198

Chapter 6 Diagnostics and troubleshooting

ENWW

Summary of Contents for Z400 - Workstation































































































































































































































































Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands

HP Z400 - Workstation, Maintenance And Service Manual

Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands