manualshive.com logo in svg

HP Z400 - Workstation, Maintenance And Service Manual

The HP Z400 Workstation is a professional-grade powerhouse designed for demanding tasks. Enhance your productivity with this high-performance device that combines speed and reliability. Find complete guidance in the Quick Reference Manual available for free download at manualshive.com. Unlock the full potential of your workstation with this comprehensive manual.

Share
Download
background image

Diagnostic codes and errors .................................................................................................. 195

Diagnostic LED and audible (beep) codes ................................................................ 195
LED color definitions .............................................................................................. 199
POST error messages ............................................................................................ 201

7  Configuring RAID devices .............................................................................................. 207

Maximum hard drive configurations ....................................................................................... 207
Configuring SATA RAID devices ............................................................................................ 208

Attaching SATA HDDs ........................................................................................... 208
Configuring system BIOS ....................................................................................... 209
Creating RAID volumes .......................................................................................... 210

Configuring SAS RAID devices .............................................................................................. 211

Supported configurations ....................................................................................... 211
SAS RAID 0 configuration ...................................................................................... 212
SAS RAID 1 configuration ...................................................................................... 213
SAS RAID 1E configuration .................................................................................... 214
Deleting RAID volumes ........................................................................................... 215

8  Configuring password security and resetting CMOS ...................................................... 216

Preparing to configure passwords .......................................................................................... 217
Resetting the password jumper ............................................................................................... 218
Clearing and Resetting the CMOS ......................................................................................... 219

Using the CMOS Button ......................................................................................... 219
Using the Computer Setup (F10) Utility to Reset CMOS .............................................. 220

Appendix A  Connector pins ............................................................................................. 221

Appendix B  System board designators ............................................................................ 231

Appendix C  Routine Care ................................................................................................. 233

General cleaning safety precautions ....................................................................................... 233
Cleaning the workstation case ............................................................................................... 233
Cleaning the keyboard ......................................................................................................... 233
Cleaning the monitor ............................................................................................................ 234
Cleaning the mouse .............................................................................................................. 234

Appendix D  Locating HP resources ................................................................................... 235

Product information .............................................................................................................. 236
Product support .................................................................................................................... 237
Product documentation ......................................................................................................... 238
Product diagnostics .............................................................................................................. 239
Product updates ................................................................................................................... 240

ENWW

xi

Summary of Contents for Z400 - Workstation































































































































































































































































Reviews:

No comments

Related manuals for Z400 - Workstation

Queclink GV Series User Manual preview
GV Series
Brand: Queclink Pages: 10
E-Mu 404 Quick Start Manual preview
404
Brand: E-Mu Pages: 12
TrekStor Pyrus WiFi Quick Manual preview
Pyrus WiFi
Brand: TrekStor Pages: 86
Farenheit TID-894NRBT Operating Manual preview
TID-894NRBT
Brand: Farenheit Pages: 63
Boca Systems BEN1PI Installation Manual preview
BEN1PI
Brand: Boca Systems Pages: 68
X-media XM-NA3500 User Manual preview
XM-NA3500
Brand: X-media Pages: 8
Avery Dennison AP5.6 User And Service Manual preview
AP5.6
Brand: Avery Dennison Pages: 103
bioscrypt V-Prox Setup Manual preview
V-Prox
Brand: bioscrypt Pages: 72
Stealth Cam STC-CRV43 Instruction Manual preview
STC-CRV43
Brand: Stealth Cam Pages: 24
OEM BT45-NIS Manual preview
BT45-NIS
Brand: OEM Pages: 18
Blaupunkt Lexington C32 Operating And Installation Instructions preview
Lexington C32
Brand: Blaupunkt Pages: 80
Boss Audio Systems 748UAI User Manual preview
748UAI
Brand: Boss Audio Systems Pages: 11
Advantech PCI-1753 User Manual preview
PCI-1753
Brand: Advantech Pages: 38
Ednet 85055 Manual preview
85055
Brand: Ednet Pages: 2
Kvaser PCIcan Reference Manual preview
PCIcan
Brand: Kvaser Pages: 21
Hama 56123 Quick Reference Manual preview
56123
Brand: Hama Pages: 6
Hama 124024 Operating Instructions Manual preview
124024
Brand: Hama Pages: 38
Blaupunkt Granada RCR 127 Operating Instructions Manual preview
Granada RCR 127
Brand: Blaupunkt Pages: 23

Brands by name

Popular brands

Load more brands