HP Z400 - Workstation Page 182 Maintenance And Service Manual Download

Page: 182 / 254

Troubleshooting checklist

Before running diagnostic utilities, use the following checklist to find possible solutions for workstation

or software problems.

●

Is the workstation and monitor connected to a working electrical outlet?

●

Is the workstation powered on?

●

Is the green power light illuminated?

●

Is the monitor on?

●

Is the green monitor light illuminated?

●

If the monitor is dim, adjust the monitor brightness and contrast controls.

●

Press and hold any key. If the system beeps, the keyboard is operating correctly.

●

Check cables for loose or improper connections.

●

After installing a non-plug and play (PnP) expansion board or other option (such as a diskette

drive), reconfigure the workstation.

●

Are all necessary device drivers installed?

●

Have all printer drivers been installed for each application?

●

Have you removed diskettes, optical disks, and USB drive keys from the drives before powering

on the workstation?

●

Are you running the latest version of BIOS, drivers, and software?

HP troubleshooting resources and tools

This section provides information on the HP Help and Support Center, E-support, and Helpful Hints for

troubleshooting.

HP Support Assistant

The HP Support Assistant is a customized HP user interface that enhances the Windows Vista and Win

7 Help and Support Center functions. This customized utility allows you to access specific information

about an HP Workstation such as configuration information by clicking

Start

Help and Support.

The interface also provides customized help and support links to the HP Web site related to the HP

Workstation.

NOTE:

The customized HP Support Assistant is not available on Windows XP Professional x32 or

x64 Editions, or on Linux.

HP Help and Support Center

The HP Help and Support Center is a customized HP user interface that enhances the Windows XP Help

and Support Center Help feature. This customized utility allows you to access specific information about

your HP Workstation such as configuration information by clicking

Start

Help and Support.

The

interface also provides customized help and support links to the HP Web site related to your HP

Workstation.

170

Chapter 6 Diagnostics and troubleshooting

ENWW

Summary of Contents for Z400 - Workstation































































































































































































































































Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands

HP Z400 - Workstation, Maintenance And Service Manual

Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands