manualshive.com logo in svg

HP Z400 - Workstation, Maintenance And Service Manual

The HP Z400 Workstation is a professional-grade powerhouse designed for demanding tasks. Enhance your productivity with this high-performance device that combines speed and reliability. Find complete guidance in the Quick Reference Manual available for free download at manualshive.com. Unlock the full potential of your workstation with this comprehensive manual.

Share
Download
background image

Testing power supply

Before replacing the power supply, use the Built-In Self-Test (BIST) feature to learn if the power supply

still works.

To test the power supply:

1.

Disconnect the AC power.

2.

Remove the internal power supply cables from the system board. (You do not need to remove the

power supply from the chassis.)

3.

If necessary, disconnect the PCIe power cable from the graphics card.

4.

Plug in AC power and verify the following:

●

If the green BIST LED on the rear of the workstation is illuminated 

and

 the fan is spinning, the

power supply is functional.

●

If the green BIST LED is not illuminated 

or

 the fan is not spinning, replace the power supply.

See the 

Rear panel components

 section of this service guide to locate the BIST LED on this workstation.

Table 6-2

  Power supply problems

Problem

Cause

Solution

Power supply shuts down
intermittently.

Power supply fault.

Replace the power supply.

Workstation powers off and the
Power LED flashes red 2 times
(once every second), followed by a
2-second pause.

Processor thermal protection is
activated.

A fan might be blocked or not
turning.

OR

The processor heatsink fan
assembly is not properly
attached to the processor.

1.

Ensure that the workstation air vents are not blocked.

2.

Open the access panel and press the workstation
power button.

3.

Verify that the system fan is running.

4.

Verify that the processor heatsink fan spins.

If the heatsink fan is not spinning, verify that the fan
cable is plugged into the system board connector.
Verify that the fan is properly seated.

5.

Replace the processor heatsink.

Power LED flashes red (once every
2 seconds).

Power failure (power supply is
overloaded).

1.

Determine whether a device is causing the problem
by performing the following:

a.

Disconnect AC power.

b.

Remove all attached devices.

c.

If necessary, disconnect the PCIe power cable
from the graphics card.

d.

Power on the workstation.

If the system enters the POST, perform the following:

a.

Power off the workstation.

b.

Replace one device at a time and repeat this
procedure until a failure occurs.

176

Chapter 6   Diagnostics and troubleshooting

ENWW

Summary of Contents for Z400 - Workstation































































































































































































































































Reviews:

No comments

Related manuals for Z400 - Workstation

Feig Electronic ID PAD74-U Installation Manual preview
ID PAD74-U
Brand: Feig Electronic Pages: 15
Glasdon ICEMASTER 25 Instruction Leaflet preview
ICEMASTER 25
Brand: Glasdon Pages: 8
StarTech.com PCI4S550 Instruction Manual preview
PCI4S550
Brand: StarTech.com Pages: 10
Blaupunkt SAINT MALO RCM 127 Operating Instructions Manual preview
SAINT MALO RCM 127
Brand: Blaupunkt Pages: 23
Jensen VR209 Installation And Operation Manual preview
VR209
Brand: Jensen Pages: 18
Alpine CDA-9831R Service Manual preview
CDA-9831R
Brand: Alpine Pages: 71
bq Cervantes 2 Quick Start Manual preview
Cervantes 2
Brand: bq Pages: 44
Exsys EX-44062 Manual preview
EX-44062
Brand: Exsys Pages: 2
Alien Skylark WMU2000 User Manual preview
Skylark WMU2000
Brand: Alien Pages: 28
Duali DE-930 User Manual preview
DE-930
Brand: Duali Pages: 12
Beltek ZR-910 Instruction Manual preview
ZR-910
Brand: Beltek Pages: 16
Trend-tech WNA015 User Manual preview
WNA015
Brand: Trend-tech Pages: 10
Alien ALH-900h User Manual preview
ALH-900h
Brand: Alien Pages: 41
CPI ALIO Pro Technician Manual preview
ALIO Pro
Brand: CPI Pages: 16
Barnes & Noble Nook BNRV350 User Manual preview
Nook BNRV350
Brand: Barnes & Noble Pages: 106
ThingMagic USB RFID Reader Setup Manual preview
USB RFID Reader
Brand: ThingMagic Pages: 16
DAQ system PCI-AIO01 User Manual preview
PCI-AIO01
Brand: DAQ system Pages: 20
Lava LAVA SSerial-PCIe Datasheet preview
LAVA SSerial-PCIe
Brand: Lava Pages: 1

Brands by name

Popular brands

Load more brands