manualshive.com logo in svg

HP Z400 - Workstation, Maintenance And Service Manual

The HP Z400 Workstation is a professional-grade powerhouse designed for demanding tasks. Enhance your productivity with this high-performance device that combines speed and reliability. Find complete guidance in the Quick Reference Manual available for free download at manualshive.com. Unlock the full potential of your workstation with this comprehensive manual.

Share
Download
background image

3 Restoring the operating system

This chapter describes how to restore the Windows or Linux operating system. It includes these topics:

Topics

Restore methods on page 24

Ordering backup software on page 25

Restoring Windows 7 or Windows Vista on page 25

Restoring Windows XP Professional on page 26

Restoring Novell SLED on page 28

Restore methods

The Windows 7 or Windows Business Vista operating system can be reinstalled using the HP

RestorePlus! process. The Windows XP Professional operating system can be reinstalled using the

RestorePlus! process or the HP Backup and Recovery Manager.

●

RestorePlus!

The RestorePlus! process reinstalls the Windows operating system and device drivers (for devices

included with the system) to a near-factory state. The process does not back up or recover data on

the hard drive. Some application software might not be restored using this process and must be

installed from the appropriate application CD.

●

HP Backup and Recovery Manager (HPBR) Recovery Point

The HP Backup and Recovery Manager application can be used to capture and restore the

contents of the system partition. It captures a snapshot of the system partition and stores it in a

Recovery Point. Everything on the system partition at the time the recovery point was made is

saved.

NOTE:

HP Backup and Restore is only supported on the HP xw6600 and xw8600

Workstations.

The Recovery Point is saved to the hard drive and can be burned to media for safekeeping.

CAUTION:

These methods restore the operating system, but not data. Data must be backed up

regularly to avoid loss.

24

Chapter 3   Restoring the operating system

ENWW

Summary of Contents for Z400 - Workstation































































































































































































































































Reviews:

No comments

Related manuals for Z400 - Workstation

EarthWay POLAR TECH 90365 Assembly Instructions preview
POLAR TECH 90365
Brand: EarthWay Pages: 5
Neilsen CT2213 Assembly And Operating Instruction preview
CT2213
Brand: Neilsen Pages: 12
Franklin BOOKMAN III BDF-4045DL (French) Mode D'Emploi preview
BOOKMAN III BDF-4045DL
Brand: Franklin Pages: 28
Birch BP-8410M User Manual preview
BP-8410M
Brand: Birch Pages: 82
Datalogic MAGELLAN 8500 Omega Product Reference Manual preview
MAGELLAN 8500 Omega
Brand: Datalogic Pages: 436
Force America SSC3100 Operation And Calibration Manual preview
SSC3100
Brand: Force America Pages: 24
impro XTT909-1-0-GB-XX Installation Manual preview
XTT909-1-0-GB-XX
Brand: impro Pages: 8
Land Pride PFS4000 Operator'S Manual preview
PFS4000
Brand: Land Pride Pages: 58
Kellfri 33-JM650 Manual preview
33-JM650
Brand: Kellfri Pages: 12
StarTech.com PCISAT2IDE1 Instruction Manual preview
PCISAT2IDE1
Brand: StarTech.com Pages: 11
CDVI STAR1M Manual preview
STAR1M
Brand: CDVI Pages: 20
Boss Audio Systems DVD-2000B User Manual preview
DVD-2000B
Brand: Boss Audio Systems Pages: 13
Metra Electronics 95-2005B Installation Instructions Manual preview
95-2005B
Brand: Metra Electronics Pages: 16
Stanley GS3-MT Installation Manual preview
GS3-MT
Brand: Stanley Pages: 64
Boss Snowplow VBX 6500 Owner'S Manual preview
VBX 6500
Brand: Boss Snowplow Pages: 32
Sony CDX-GT260MP Service Manual preview
CDX-GT260MP
Brand: Sony Pages: 44
Sony CDX-G2050UP Operating Instructions Manual preview
CDX-G2050UP
Brand: Sony Pages: 20
Sony CDX-GT270MP Operating Instructions Manual preview
CDX-GT270MP
Brand: Sony Pages: 96

Brands by name

Popular brands

Load more brands