HP Z400 - Workstation Page 19 Maintenance And Service Manual Download

Page: 19 / 254

Rear panel components

The following figure shows the rear panel of a typical workstation configuration.

Figure 1-5

Rear panel

NOTE:

The rear panel connectors are labeled with industry-standard icons and colors to assist in

connecting peripheral devices.

With the optional 600W power supply, rear appearance and BIST LED location differ.

Table 1-3

Rear panel connectors

Item

Symbol

Description

Item

Symbol

Description

Power supply Built-In Self Test (BIST)
LED

Padlock

loop

Universal chassis clamp opening

Graphics card connector

PS/2 mouse connector (green)

Audio line-out connector (green)

USB 2.0 ports (4)

Microphone connector (pink)

RJ-45 network connector

USB 2.0 ports (2)

Audio line-in connector (blue)

PS/2 keyboard connector (purple)

Cable lock slot

Power cord connector

ENWW

Product features

Summary of Contents for Z400 - Workstation































































































































































































































































Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands

HP Z400 - Workstation, Maintenance And Service Manual

Search results

Summary of Contents for Z400 - Workstation

Reviews:

Related manuals for Z400 - Workstation

Brands by name

Popular brands