HP StorageWorks X9720 Administrator'S Manual Download Page 79

Page: 79 / 187

13 Upgrading the X9720 Network Storage System

hardware

WARNING!

Before performing any of the procedures in this chapter, read the important warnings,

precautions, and safety information in

“Warnings and precautions” (page 168)

and

“Regulatory

compliance and safety” (page 172)

Adding new server blades

NOTE:

This requires the use of the Quick Restore DVD. See

“Recovering the X9720 Network

Storage System” (page 125)

for more information.

On the front of the blade chassis, in the next available server blade bay, remove the blank.

Prepare the server blade for installation.

Install the server blade.

Adding new server blades

Summary of Contents for StorageWorks X9720




























































































































































































Search results

Summary of Contents for StorageWorks X9720

Reviews:

Related manuals for StorageWorks X9720

Brands by name

Popular brands

HP StorageWorks X9720, Administrator'S Manual

Search results

Summary of Contents for StorageWorks X9720

Reviews:

Related manuals for StorageWorks X9720

Brands by name

Popular brands