HP StorageWorks X9720 Administrator'S Manual Download Page 128 | Manualshive

Page: 128 / 187

background image

5.

The Verify Configuration window shows the configuration received from the management
console. Select

Accept

to apply the configuration to the server and register the server with the

management console.

NOTE:

If you select

Reject

, the wizard will exit and the shell prompt will be displayed. You

can restart the Wizard by entering the command

/usr/local/ibrix/autocfg/bin/menu_ss_wizard

or logging in to the server again.

6.

If the specified hostname already exists in the cluster (the name was used by the node you
are replacing), the Replace Existing Server window asks whether you want to replace the
existing server with the node you are configuring. When you click

Yes

, the replacement node

will be registered.

7.

After the server is registered, you will be asked whether you want to configure a passive agile
management console on the node. If the node being restored previously hosted the agile
management console, install the passive management console.

128

Recovering the X9720 Network Storage System

«
...
126
127
128
129
130
...
»

Summary of Contents for StorageWorks X9720




























































































































































































Reviews:

No comments

Related manuals for StorageWorks X9720

Verizon DSL-2750B

Brand: D-Link Pages: 6

Brand: D-Link Pages: 10

Brand: D-Link Pages: 38

MatrixPRO-II DVI 16x16

Brand: Barco Pages: 43

Brand: Barco Pages: 5

Brand: Patton electronics Pages: 8

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brand: Teagle Pages: 40

EK-FC285 GTX Classified

Brand: ekwb Pages: 2

Brand: Intel Pages: 26

Brand: Airlink101 Pages: 46

Brand: IMC Networks Pages: 36

Brand: Renesas Pages: 746

Brand: Hama Pages: 25

Brand: Infoblox Pages: 16

Brand: IEI Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands