HP StorageWorks X9720 Administrator'S Manual Download Page 143

Page: 143 / 187

Select

NTP Servers

from the menu, and enter the IP addresses or hostnames for the primary

and secondary NTP servers.

10.

Select

Networks

from the menu. You will need to create one cluster network interface, which

will be used for intracluster communication. Typically this interface is configured as

bond0

You may also need to create a user network, which is used for server to client communication.
The user network is typically

bond1

. To create a bond, select

Configuring the management console on the dedicated (non-agile) Management Server blade

143

Summary of Contents for StorageWorks X9720




























































































































































































Search results

Summary of Contents for StorageWorks X9720

Reviews:

Related manuals for StorageWorks X9720

Brands by name

Popular brands

HP StorageWorks X9720, Administrator'S Manual

Search results

Summary of Contents for StorageWorks X9720

Reviews:

Related manuals for StorageWorks X9720

Brands by name

Popular brands