manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Share
Download
HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 76

Installing the 

Installing the frame

frame into the rack

 into the rack

WARNING: 

WARNING: When lifting the frame with the optional removable handles, always use at least four

people to lift the frame into the rack. If the frame is being loaded into the rack above chest level,

a fifth person must assist with aligning the frame with the rails while the other four people

support the weight of the frame.

NOTE: 

NOTE: You can install the frame into the rack using a mechanical lift. When using a mechanical lift, two people are

required for the frame installation. If you choose the mechanical lift installation, resume the frame installation at step 5.

Procedure

Procedure

1.  Attach the lift handles to the  frame.

a.  Align each lift handle to the  frame spools.

b.  Press the release button, and then pull the lift handle up until it locks in place.

2.  Line up the  frame with the rack, set the back end of the  frame on the rack rails and slide it in.

Installing the frame into the rack

76

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands