HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 72

Page: 72 / 183

Measuring with the rack template

The HPE Synergy 12000 Frame Rack Template ships with the frame. The rack template provides detailed instructions on where to

position the frame and rack rails, and where to install the cage or clip nuts. Each frame kit includes the rack rails recommended for that

frame.

NOTE:

NOTE: Four cage nuts and four clip nuts are included with the frame. Always use cage nuts in racks with square holes.

Always use clip nuts in racks with round holes.

When installing multiple frames, install the rack rails and cage nuts for one frame, and then install the frame. Repeat for each additional

frame.

Procedure

1. Install lower cage nuts (left and right) in the front of the rack at the bottom of the fourth U (10 holes up on the template).

2. Install the upper cage nuts (left and right) in the front of the rack at the bottom of the tenth U (28 holes up on the template).

3. Install the rack rails.

Measuring with the rack template

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands