manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Share
Download
HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 44

11

LINK port

SFP+ connector that provides the following functions:

IMPORTANT:

IMPORTANT:

Use supported SFP+ 10GbE DAC cables or transceivers for LINK port
connections. For more information, see the product QuickSpecs on the
Hewlett Packard Enterprise website

Hewlett Packard Enterprise website .

Provides high availability management network connectivity between:

LINK ports on two frame link modules in the same frame for a single frame
configuration

Frame link modules in different frames as part of a management network ring in
a multiframe configuration

Provides management ring (frame link topology) connectivity for automatic frame
discovery by HPE OneView.

12

MGMT port

SFP+ connector that provides the following functions:

IMPORTANT:

IMPORTANT:

Use supported SFP+ DAC cables or transceivers for MGMT port connections.
For more information, see the product QuickSpecs on the Hewlett Packard

Hewlett Packard

Enterprise website

Enterprise website.

IMPORTANT:

IMPORTANT:

The transceiver or cable used must match the port speed of the switch used
for management network connectivity.

Provides a management uplink to the management network.

10GbE or 1GbE based on the cable or transceiver used.

Item

Item

Description

Description

Function

Function

HPE Synergy 4-Port Frame Link Module components and LEDs

44

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands