manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Share
Download
HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 39

Storage module LEDs

Storage module LEDs

The front panel and LED layout shown in the following illustration is an example. Depending on your specific model, the LEDs might be

different.

Item

Item LED

LED

Status

Status

Definition

Definition

1

Drawer status

Solid green

Drive drawer is closed

 

 

Flashing green Drive drawer is open

 

 

Flashing amber Thermal warning, close the drive drawer

2

UID

Solid blue

One or more drives are being located

 

 

Flashing blue

Firmware flash in progress

 

 

Off

No drives are being located

3

Health status

Green

Normal operation

 

 

Flashing amber Degraded condition

 

 

Flashing red

Critical condition

4

Drive status (in priority order) Solid amber

One or more drives failed

 

 

Flashing amber One or more drives are predicted to fail

 

 

Flashing green One or more drives are rebuilding or transforming

 

 

Solid green

One or more drives are members of a logical drive

 

 

Off

No drives are configured by a RAID controller

5

Drawer power

Green

Storage module is in use, do not remove

 

 

Off

Storage module is not in use, safe to remove

The drive drawer must be closed within five minutes after it is opened.

1

1

Storage module LEDs

39

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands