manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Share
Download
HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 46

6

USB port

Allows connection to the frame using a supported USB device. Devices include a
keyboard or mouse for connecting to the HPE Synergy Console. To connect multiple
devices, a USB hub (not included) is required.

Used for performing a USB recovery frame link module firmware update.

7

LINK port activity
LED

Reports LINK port activity:

Flashing green = Activity on the LINK port

Off = No activity on the LINK port

8

LINK port

A 10GBASE-T RJ45 connector that provides two functions:

Provides high-availability management network connectivity between:

LINK ports on two frame link modules in the same frame for a single frame
configuration.

Frame link modules in different frames as part of a management network ring in
a multiframe configuration.

Provides management ring (frame link topology) connectivity for automatic frame
discovery by HPE OneView.

9

LINK port
connectivity LED

Reports LINK port connectivity:

Solid green = LINK port is connected.

Off = LINK port is not connected.

10

Monitor port

Allows connection to the frame using a monitor device or an active monitor port
adapter.

Item

Item

Description

Description

Function

Function

HPE Synergy Frame Link Module components and LEDs

46

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands