HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 108

Page: 108 / 183

Half-height

Half-height compute module

compute module mezzanine connector definitions

mezzanine connector definitions

NOTE:

NOTE: The compute module hood label includes the exact mezzanine card locations.

Item

Item Mezz slot

Mezz slot

connector

identification

Supported

card types

Fabric

Fabric Interconnect bay sets

Interconnect bay sets

Mezzanine
slot 1 (M1)

Type C
and Type
D

ICM 1 and 4

Mezzanine
slot 2 (M2)

Type C
and Type
D

ICM 2 and 5

Mezzanine
slot 3 (M3)

Type C
only

ICM 3 and 6

When installing a mezzanine option in mezzanine slot 2, processor 2 must be installed.

Half-height compute module mezzanine connector definitions

108

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands