HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 120

Page: 120 / 183

Cabling the

Cabling the frame

frame

WARNING:

To reduce the risk of electric shock or injury due to high-current electrical energy, be sure that

all power is completely disconnected at the source before beginning any power connections to

the power bus bars or power bus box.

WARNING:

Be sure that all circuit breakers are locked in the off position before connecting any power

components.

Prerequisites

Download and review the HPE Synergy Cabling Guide from the Hewlett Packard Enterprise website (https://www.hpe.com/info/synergy-

https://www.hpe.com/info/synergy-

docs

docs).

Procedure

1. Cable the management network ports (MGMT and LINK).

2. Cable the HPE Synergy Image Streamer management ports.

3. Cable the interconnect modules.

4. Connect the power cables. Connect to the power source in your facility to each of the installed power supplies, and power up the

frame.

5. To configure HPE Synergy, connect to the HPE Synergy Console.

Cabling the frame

120

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands