HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 64

Page: 64 / 183

UID LED/button

Solid blue = Activated
Flashing blue = Firmware upgrade in progress

Off = Deactivated

Health LED

Solid green = Normal
Solid amber = No power present

Flashing amber = Module degraded

Solid red = A physical alignment error exists.

Link/Activity mode LED

Solid green = Link/Activity mode is selected.

PID mode LED

Solid green = PID mode is selected.

Ethernet mode LED

Solid green = Ethernet mode is selected.

Fibre Channel (FC) mode
LED

Solid green = FC mode is selected.

Item

Description

Status

See OneView (http://www.hpe.com/info/oneview/docs

http://www.hpe.com/info/oneview/docs)

Remove and then reinstall the module.

When illuminated, QSFP+ port LEDs indicate the port operating states for each of the uplink ports in the selected mode.

1
2
3

HPE Synergy 40Gb F8 Switch Module LEDs and buttons

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands