HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 16

Page: 16 / 183

Temperature requirements

To ensure continued safe and reliable equipment operation, install or position the rack in a well-ventilated, climate-controlled

environment.

The operating temperature inside the rack is always higher than the room temperature and is dependent on the configuration of

equipment in the rack. Check the TMRA for each piece of equipment before installation.

CAUTION:

To reduce the risk of damage to the equipment when installing third-party options:

Do not permit optional equipment to impede airflow around the frame or to increase the internal rack temperature
beyond the maximum allowable limits.

Do not exceed the manufacturer’s TMRA.

Temperature requirements

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands