manualshive.com logo in svg

HP 85106D, Manual

The HP 85106D user manual is available for free download on our website. This comprehensive manual provides detailed instructions and essential information on operating and maximizing the performance of your HP 85106D. Enhance your product experience by accessing this user manual at manualshive.com.

Share
Download
background image

Contents-viii

HP 85106D mm-Wave System

A2 IF Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-41

Figure 6-24. Multiplexer Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-41
Figure 6-25. HP 85105A Power Supply Block Diagram. . . . . . . . . 6-42
Figure 6-26. HP 85105A mm-Wave Controller Block Diagram . . . 6-43

Replaceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-45

R-E (Rebuilt-Exchange) Assemblies Cost Less . . . . . . . . . . . . . . . 6-45
Replaceable Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-45
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-45
Figure 6-27. The Low Cost Rebuilt Exchange Procedure . . . . . . . . 6-47
Figure 6-28. HP 85105A Major Assemblies . . . . . . . . . . . . . . . . . . 6-48
Table 6-4. HP 85105A Major Assembly Parts . . . . . . . . . . . . . . . . 6-49
Figure 6-29.

HP 85105A Semi-rigid RF Cables . . . . . . . . . . . . . 6-50

Table 6-5. HP 85105A Semi-rigid RF Cable Parts . . . . . . . . . . . . . 6-51
Figure 6-30. HP 85105A Flexible RF Cables . . . . . . . . . . . . . . . . . 6-52
Table 6-6. Flexible RF and Ribbon Cable Parts . . . . . . . . . . . . . . . 6-52
Figure 6-31. Wire Harnesses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-54
Table 6-7. Wire Harness Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-55
Figure 6-32. HP 85105A Front Panel . . . . . . . . . . . . . . . . . . . . . . . 6-56
Table 6-8. HP 85105A Front Panel Miscellaneous Parts . . . . . . . . 6-57
Figure 6-33. Rear Panel (Standard, Option 050) . . . . . . . . . . . . . . 6-58
Table 6-9. Rear Panel Miscellaneous Parts

(Standard, Option 050) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-59

Figure 6-34. Detailed Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-60
Figure 6-35. Fuse Locations and Values . . . . . . . . . . . . . . . . . . . . 6-61
Table 6-10. Fuse Locations, Values and Parts . . . . . . . . . . . . . . . . 6-61
Figure 6-36. HP 85105A (Options 004 and O50) Unique Semi-Rigid

Cable Assemblies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-62

Table 6-11. HP 85105A (Options 004,050) Unique Semi-Rigid Cable

Assembly Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-63

Figure 6-37.

HP 85105A Accessories (Standard) . . . . . . . . . . . . 6-64

Table 6-12. HP 85105A Accessories (Standard). . . . . . . . . . . . . . . 6-65
Figure 6-38.

HP 85105A Accessories (Option 050) . . . . . . . . . . 6-66

Table 6-13. HP 85105A Accessories (Option 050) . . . . . . . . . . . . . 6-67
Figure 6-39.

Chassis Parts, all HP 85105A Models . . . . . . . . . . 6-68

Table 6-14. All 85105A Model Chassis Parts . . . . . . . . . . . . . . . . . 6-69
Figure 6-40. Power Cable and Plug Part Numbers . . . . . . . . . . . . 6-70

A.

HP-IB Addresses, Hardware States, and Instrument States

Table A-1. HP 85106D mm-Wave System HP-IB Addresses. . . . . . . A-1
Table A-2. Important HP 85106D mm-Wave Hardware States. . . . . A-1
Table A-3. Important HP 85106D mm-Wave System

Instrument States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

TableA-4. HP85106Dmm-waveSystemMultipleSourceOperatingFrequencies

A-2

B.

Upgrade Paths

Network Analyzer Upgrade Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Related manuals for 85106D

Abbott CELL-DYN 3000 Troubleshooting Manual preview
CELL-DYN 3000
Brand: Abbott Pages: 296
AccuEnergy Acuvim-L Series User Manual preview
Acuvim-L Series
Brand: AccuEnergy Pages: 83
B meters IWM-TX5 Quick Start Manual preview
IWM-TX5
Brand: B meters Pages: 2
dacell DN-10 User Manual preview
DN-10
Brand: dacell Pages: 22
MADDALENA ElecTo Bulk Installation Instructions preview
ElecTo Bulk
Brand: MADDALENA Pages: 4
Macnaught M1 SERIES Instruction Manual preview
M1 SERIES
Brand: Macnaught Pages: 4
PASCO PS-3215 Battery Replacement preview
PS-3215
Brand: PASCO Pages: 3
Campbell Wind Monitor Series Instruction Manual preview
Wind Monitor Series
Brand: Campbell Pages: 38
Favero Electronics ASSIOMA UNO Test preview
ASSIOMA UNO
Brand: Favero Electronics Pages: 12
Nidec FG-3000R Series Operation Manual preview
FG-3000R Series
Brand: Nidec Pages: 8
Datcon DT4120 PS Series Operating Instructions Manual preview
DT4120 PS Series
Brand: Datcon Pages: 92
MADDALENA Arrow Mobile Android Quick Start Manual preview
Arrow Mobile Android
Brand: MADDALENA Pages: 12
Saluki Technology S3302A Datasheet preview
S3302A
Brand: Saluki Technology Pages: 161
Westfalia 91 38 20 Original Instructions Manual preview
91 38 20
Brand: Westfalia Pages: 18
DIALAB DTN-410 K User Manual preview
DTN-410 K
Brand: DIALAB Pages: 20
Vega SI-11 User Manual preview
SI-11
Brand: Vega Pages: 24
Anritsu MS2024A Maintenance Manual preview
MS2024A
Brand: Anritsu Pages: 15
MONARCH INSTRUMENT 6241-010 Instruction Manual preview
6241-010
Brand: MONARCH INSTRUMENT Pages: 28

Brands by name

Popular brands

Load more brands