manualshive.com logo in svg

HP 85106D, Manual

The HP 85106D user manual is available for free download on our website. This comprehensive manual provides detailed instructions and essential information on operating and maximizing the performance of your HP 85106D. Enhance your product experience by accessing this user manual at manualshive.com.

Share
Download
background image

1-10

HP 85106D mm-Wave System

Getting Started

Preparing the Site

Preparing the Site

The environmental and electrical requirements needed to operate your
HP 85106D system are specified in this section. Make sure the site meets
the requirements listed in Table 1-5, before you begin installation.

Environmental
Requirements

Notice that the requirements for the HP 85106D are the same as for the
HP 8510C network analyzer. Note the accuracy enhanced, measurement
requirements that follow. Keep the environment as dust-free as possible.
Clean the air filters and the system rack regularly.

Accuracy Enhanced
Measurement
Requirements

Accuracy enhanced (error corrected), measurements require the ambient
temperature of the HP 85106D system to be maintained within

±

1°C of the

ambient temperature at the time of calibration. The calibration temperature
must be within the operating temperature range of the calibration kit
(typically 20° to 26°C). See the appropriate calibration kit manual for
actual operating temperature values.

Power Requirements

Install the required ac power at all necessary locations. Place air-condition-
ing equipment or any other motor-operated equipment on a different ac line
than the one used by the system.

Only use three-wire power cables for all the instruments. These cables pro-
vide the required grounding when they are connected to a grounded power
outlet. Table 1-6 on page 1-11 lists the maximum VA power ratings of the
HP instruments in this system.

System Heating and
Cooling

Install air conditioning and heating if required. Air conditioning require-
ments depend on the amount of heat produced by the instruments. Use the
BTU/hour ratings from Table 1-6 on page 1-11 to determine the total rating
of your system. Each VA rating is multiplied by 3.4 to determine the
BTU/hour rating of each instrument.

To convert the total BTU/hour figure to “tons,” divide the total BTU/hour
value by 12,000. A “ton” is the amount of heat required to melt a ton
(907 kg) of ice per hour.

Table 1-5

HP 85106D Environmental Requirements

Temperature

+5° C to 40° C (41° F to 104°F)

Relative Humidity

5% to 95% at +40°C or less (non-condensing)

Altitude

Up to 4600 meters (approximately 15,000 feet)

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Related manuals for 85106D

4iiii PRECISION Firmware Upgrade Instructions preview
PRECISION
Brand: 4iiii Pages: 3
Accu-Chek Inform II Training Manual preview
Inform II
Brand: Accu-Chek Pages: 12
Eagle Eye Power Solutions Vigilant ELM Series Troubleshooting Manual preview
Vigilant ELM Series
Brand: Eagle Eye Power Solutions Pages: 9
Narvitech NS110 Quick Manual preview
NS110
Brand: Narvitech Pages: 2
National Instruments PXIe-5665 Calibration Manual preview
PXIe-5665
Brand: National Instruments Pages: 85
National Instruments PXIe-5622 Getting Started Manual preview
PXIe-5622
Brand: National Instruments Pages: 12
National Instruments PXIe-4163 Manual preview
PXIe-4163
Brand: National Instruments Pages: 18
National Instruments USB-5683 Getting Started Manual preview
USB-5683
Brand: National Instruments Pages: 12
DAKOTA ULTRASONICS ZX-3 Operation Manual preview
ZX-3
Brand: DAKOTA ULTRASONICS Pages: 38
CA.MI T-PLUS User Manual preview
T-PLUS
Brand: CA.MI Pages: 68
Nidec FG-3000R Series Operation Manual preview
FG-3000R Series
Brand: Nidec Pages: 8
Floyd Rose SPEEDLOADER BRIDGE SYSTEM Manual preview
SPEEDLOADER BRIDGE SYSTEM
Brand: Floyd Rose Pages: 10
Jaquet T411 Operating Instructions Manual preview
T411
Brand: Jaquet Pages: 27
Fora GTel Owner'S Manual preview
GTel
Brand: Fora Pages: 64
Campbell HydroSense II User Manual preview
HydroSense II
Brand: Campbell Pages: 37
Ofs udox Operating Instructions Manual preview
udox
Brand: Ofs Pages: 28
Hach DOC026.52.00769 User Manual preview
DOC026.52.00769
Brand: Hach Pages: 64
Agilent Technologies 10400B Series User Manual preview
10400B Series
Brand: Agilent Technologies Pages: 20

Brands by name

Popular brands

Load more brands