manualshive.com logo in svg

HP 85106D, Manual

Share
Download
HP 85106D Manual Download Page 151

5-38

HP 85106D mm-Wave System

HP 85104A Test Set Module

Assembly Procedure

15. Attach a mixer/isolator assembly to each mixer clamp by aligning the

isolator flange with the coupler interface (use the guide pins). Follow the
waveguide connection procedure in step 5 of this procedure to connect
the flanges.

16. Attach a mixer bracket to each mixer using two screws on the mixer

clamp and two screws on the coupler bracket.

17. Attach the semi-rigid coaxial cables from the LO power divider to the

mixers; W10 to the left mixer and W11 to the right mixer.

18. Attach the IF cables to the mixers (red/white to the incident mixer and

blue/white to the reflected mixer).

19. Attach the RF and LO cables (part of the rear panel/cable assembly) to

the coaxial elbows on the top mount.

20. Slide the front panel into the groove of the top housing.

NOTE 

The grommet in the front panel should move freely after the bottom housing
is tightened down.

21. Attach the long flexible cables to a bracket or piece of waveguide with a

cable tie.

22. Attach the bottom housing using two torx-head screws.

23. Attach the stand to the module by aligning the two captive screws with

the module and tightening them. Refer to Chapter 1, “Getting Started”
for the procedure to attach the stand.

24. To complete the assembly procedure, reattach the test port extensions

(straight sections and bends) to the test port.

NOTE 

Perform the operator's check for the HP 85106D system located in
Chapter 2, “Operation” of this manual. If the unit is working, a performance
verification should be done to assure that the system is operating within its
specifications. Refer to Chapter 3, “Performance Verification” in this manual
for information.

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands