Home
/
HP
/
85106D
/
Manual

HP 85106D, Manual

Share

Page: 41 / 244

HP 85106D Manual Download Page 41

1-22

HP 85106D mm-Wave System

Getting Started

Making Connections

Making Connections

The HP-IB Bus

The computer retains full control of the HP-IB bus. No other device can
send commands until the computer relinquishes its control. Connect any
peripheral equipment to this bus if you want the equipment to be controlled
by the computer only.

Connecting a Plotter

To connect a plotter to the system:

•

Attach one end of the HP-IB cable to the plotter (the plotter should have
its own HP-IB cable).

•

Then attach the "free" end of the plotter cable to either the "HP 8510
Interconnect" (for system bus control), or to the "HP-IB Connector"
(for HP-IB bus control).

•

Set the plotter address to 5.

•

Connect the plotter to an ac-power source and then turn it ON.

Refer to “Accessory ac Power Outlet” on page 1-22" for information about
connecting the plotter to the power outlet inside the system cabinet.

Accessory ac Power
Outlet

All power connections for instruments in the system are located inside the
cabinet via a multiple-outlet power strip. On some systems an extra power
outlet is provided on the power strip for accessories. Power cables for
accessories may be routed through the hole provided in the rear of the
cabinet. Special “boot” ac power cables are included with your HP 85106D
system for this purpose.

CAUTION

Before connecting any equipment to the extra power outlet refer to Table 1-6
on page 1-11 for the maximum VA ratings for this outlet on your system.

Installing the
HP 85106D Into a
Different Cabinet

Hewlett-Packard strongly recommends that the HP 85106D system cabinet
be used with the HP 85106D mm-wave system. HP is not obligated to
support user-configured mm-wave rack systems. The customer takes full
responsibility for instrument damage incurred due to using racks or system
cabinets other than the one supplied with the HP 85106D system. Contact
your nearest HP Sales and Service Office for more information about
ordering a rack for your system.

«
...
39
40
41
42
43
...
»

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands