manualshive.com logo in svg

HP 85106D, Manual

Share
Download
HP 85106D Manual Download Page 8

HP 85106D mm-Wave System

vii

Safety and Regulatory Information

Review this product and related documentation to familiarize yourself with
safety markings and instructions before you operate the instrument. This
product has been designed and tested in accordance with international
standards.

WARNING 

The WARNING notice denotes a hazard. It calls attention to a procedure, 
practice, or the like, that, if not correctly performed or adhered to, could result 
in personal injury. Do not proceed beyond a WARNING notice until the 
indicated conditions are fully understood and met.

CAUTION 

The CAUTION notice denotes a hazard. It calls attention to an operating
procedure, practice, or the like, which, if not correctly performed or adhered
to, could result in damage to the product or loss of important data. Do not
proceed beyond a CAUTION notice until the indicated conditions are fully
understood and met.

Instrument Markings

When you see this symbol on your instrument, you should refer to the instrument’s 
instruction manual for important information.

This symbol indicates hazardous voltages.

The laser radiation symbol is marked on products that have a laser output.

This symbol indicates that the instrument requires alternating current (ac) input.

The CE mark is a registered trademark of the European Community. If it is 
accompanied by a year, it indicates the year the design was proven.

The CSA mark is a registered trademark of the Canadian Standards Association.

1SM1-A

This text indicates that the instrument is an Industrial Scientific and Medical Group 1 
Class A product (CISPER 11, Clause 4).

This symbol indicates that the power line switch is ON.

This symbol indicates that the power line switch is OFF or in STANDBY position.

!

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands