HP 85106D Manual Download Page 135

Page: 135 / 244

5-18

HP 85106D mm-Wave System

HP 85104A Test Set Module

Troubleshooting Procedures

Figure 5-6 Power Level Test Setup

NOTE

It may be necessary to connect a waveguide straight section to the end of the
power sensor to reach the A13 output.

6. Reconnect the cables from the HP 85104A to the HP 85105A. Turn the

HP 85105A ON. Read the power level on the power meter. Refer to the
Table 5-3 on page 5-16 for the correct power level of the band you are
using.

7. Reverse the steps in this procedure to reassemble the test set module.

8. Return to the troubleshooting flowchart.

Table 5-4

RF Power Out of the A13 Source Block

Band (GHz)

Power Level (dBm)

33 to 50 (Q-band)

40 to 60 (U-band)

50 to 75 (V-band)

75 to 110 (W-band)

Summary of Contents for 85106D





















































































































































































































































Search results

Summary of Contents for 85106D

Reviews:

Brands by name

Popular brands

HP 85106D, Manual

Search results

Summary of Contents for 85106D

Reviews:

Brands by name

Popular brands