HP 85106D Manual Download Page 209 | Manualshive

Page: 209 / 244

background image

HP 85106D mm-Wave System

6-45

HP 85105A mm-Wave Controller

Replaceable Parts

Replaceable Parts

This section contains information for ordering replaceable parts. The
replaceable parts include major assemblies and chassis hardware.

R-E
(Rebuilt-Exchange)
Assemblies Cost Less

Some assemblies are available through the rebuilt-exchange program.
These factory rebuilt (repaired and tested) assemblies meet all factory
specifications required of a new assembly. They are offered on an exchange
(trade-in) basis only. The defective assembly must be returned for credit.
Figure 6-27 on page 6-47 illustrates the procedure. The rest of the figures
provide parts information. If you have any questions, contact your HP
customer engineer.

Replaceable Parts List

The following figures assist in locating and identifying all replaceable parts,
including corresponding lists that provide the following information.

•

Hewlett-Packard part number.

•

Part quantity as shown in the figure. There may be more of the same part
in the instrument.

•

Part description, using abbreviations.

Ordering Information

To order a part listed in the replaceable parts lists:

•

Quote the Hewlett-Packard part number.

•

Indicate the quantity required.

•

Address the order to the nearest Hewlett-Packard office.

To order a part that is not listed:

•

Include the instrument model number.

•

Complete serial number.

•

Description and function of the part.

•

Number of parts required.

•

Address the order to the nearest Hewlett-Packard office.

«
...
207
208
209
210
211
...
»

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Related manuals for 85106D

Brand: dacell Pages: 22

Brand: CA.MI Pages: 68

Brand: Det-Tronics Pages: 18

Brand: Aqualytic Pages: 130

Brand: SANKO Pages: 97

Brand: Staco Energy Pages: 2

Photo Research PR-810

Brand: Jadak Pages: 120

Brand: Hanna Instruments Pages: 2

Smart Photometer System iDip 570

Brand: eXact Pages: 16

Brand: QuantAsylum Pages: 35

Brand: Omega Pages: 22

Brand: Lafayette Instrument Pages: 12

WTW pH/ION 3310

Brand: Xylem Pages: 48

Brand: LOVATO ELECTRIC Pages: 9

Brand: Raycus Pages: 86

Brand: Environmental Express Pages: 17

28APE190008/AI481

Brand: Apera Instruments Pages: 13

BIP LD2-T017-01-EP-S4 Series

Brand: Balluff Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands