manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Hardware Installation And Configuration Manual

Share
Download
Honeywell MAXPRO NVR Hybrid PE Hardware Installation And Configuration Manual Download Page 130

C O N F I G U R I N G   M A X P R O   N V R

Configuring the Cameras

130

 MAXPRO NVR 5.0 Installation and Configuration Guide

6

• Over configuration of the system can lead to unsatisfactory performance.

•

Storage Calculator 

provides recording storage estimate based on the 

recording configuration (bit rate estimate of cameras, recording schedule and 
retention) of current cameras on NVR versus the maximum Recording storage 
drive space supported by the NVR in graphical manner (Percentage recording 
storage estimate is displayed and the indicator changes to red if the storage 
estimated is above the NVR recording storage capacity).

Tip: 

 Hover the mouse over the Storage Calculator indicator for more details.

Note:

• Archival storage calculations is not included in the estimation.
• This is an estimate for reference purpose only. While providing a reasonable 

storage estimate it should not be inferred that the results are absolute and will 
apply to all the systems and locations.

• Recording bit-rate and duration can be dramatically effected by PTZ 

cameras, higher levels of activity, image quality, light levels and noise.

• All the Estimator calculations are based on the fixed bit rate (Mbps) and 

might vary based on the site environment if the camera is set to VBR (variable 
bit rate) mode.

Tip: 

Click on the Status Monitor icon 

 to launch status monitor. Refer to the 

MAXPRO 

NVR Operator’s Guide

 for more information on using MAXPRO Status Monitor.

Summary of Contents for MAXPRO NVR Hybrid PE









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands