manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Hardware Installation And Configuration Manual

Share
Download
Honeywell MAXPRO NVR Hybrid PE Hardware Installation And Configuration Manual Download Page 120

C O N F I G U R I N G   M A X P R O   N V R

Configuring the System Settings

120

 MAXPRO NVR 5.0 Installation and Configuration Guide

6

Note:

The default Archival Schedule configured and recommended is Every Day at
12:00 AM. This is recommended versus the Auto [24/7] option for optimal
performance and load on NVR. 

The default Archival Schedule configured and recommended is Every Day at 12:00 AM. This is 
recommended versus the Auto [24/7] option for optimal performance and load on NVR.

Edge Sync Settings

Edge Sync settings enables you to set the schedule for synchronizing the recordings from the 
camera SD card. This feature is supported for Profile-G compliant cameras where the 
recordings are stored at the camera level.

Under 

Edge Sync Recording at:

•

Click 

Every 

option and then select the time in minutes or hours to synchronize the 

recordings.
Or
Click 

Every Day at 

option

 

to set the specific time in hours during which the 

synchronizing should trigger.

•

Limit Past Sync

: This option allows you to set number of days passed for which you 

want system to sync the recordings from camera. For example - if you set 10 days, 
then system will sync the recording within last 10 days from camera.

Manual Archival

Manual archive can be performed in Search tab. You need to search and then archive the 
required recording. Before performing the manual archive ensure that you configure the drive 
in Disk tab and select the Drive Purpose as Archival. See 

Configuring the Disk Management 

Settings 

section on page 

122

.

To perform manual archive

:

1.

Navigate to 

Search

 tab and search the required 

Recording

. Refer 

MAXPRO NVR 

Operator’s Guide

, 

How to search for recorder video and events

 section for more 

information. The recorded video is searched based on the search conditions. The search 
results are listed in the 

Results

 window.

2.

In the 

Results

 pane, select the required recording from the list of recording. Press 

Ctrl

 to 

select multiple recordings.

Summary of Contents for MAXPRO NVR Hybrid PE









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands