Honeywell BC-200, Operation, Installation & Programming Manual, Page: 124 / 156

Appendix
BC-200 Manual – P/N DOC-01-013 124
9.7 M
ODEM
/P
RINTER
/HLI I
NTERFACE
9 9 . . 7 7 . . 1 1 M M
O
O
D
D
E
E
M
M
I I
N
N
T
T
E
E
R
R
F
F
A
A
C
C
E
E
The BC-200 PC Interface can be used to control the FIP using a modem and BC-200 PCI software. A global
option on the FIP will enable/disable modem operation.
9.7.1.1 PC M
ODEM
Any non software modem should work correctly with the PCI. It is recommended to use a high quality external
modem to allow modifying of modem parameters to solve any possible compatibility issues.
9.7.1.2 FIP M
ODEM
The recommended modem for the FIP is a NetComm IG6000 (industrial modem) that is modified to work with
24VDC. This modem was chosen due to its construction and reliability.
9.7.1.3 FIP M
ODEM
S
ETTINGS
The FIP modem needs to be programmed with the following AT commands using a terminal program such as
HyperTerminal and the standard modem to PC cable provided:
Use “AT S0=2 R115 &K3 &S0 %E2” command to set the required modem options
ATS0=2 - answer after 2 rings
ATR115 - lock terminal speed to 115000
AT&K3 - RTS/CTS flow control
AT&S0 - DSR signal always asserted
AT%E2 - Automatic speed stepping
To establish connection with the modem after the above commands have been entered, set HyperTerminal port
settings to 115 baud rate & RTS/CTS handshaking.
After re-connecting to the modem using the above settings, save the configuration to hardware profile 0 using the
AT&W0 command.
Check modem configuration using AT&V command. Ensure that all the options are the same as the configuration
printout below:
B0 E1 L1 M1 T Q0 R115 V1 W2 X5 &B4 &C1 &D2 &G0 &H0 &K3 &L0 &M0 &N1 &P1 &R0 &S0
&T4 &X0 &Y0 \A3 \B3 \J0 \K5 \N3 \T0 \V0 \X0 #A2 #B0 #C0 #D0 #E0 #F0 #I0 #J1
#M0 #N0 #O0 #Q0 #U0 #V0 %B0 %C3 %D0
%E2 %F1 %G0 %H0 %K0 %L11 %M0 %N0 %P0 %R0
%S0 %T0 %U0 %V0 %W0 *K0 *V0 *R0 *T0 *Y0 -Q1 :E1 -SDR0,1 #CID0 #MUS0
S000:002 S002:043 S003:013 S004:010 S005:008 S006:004 S007:050 S008:004
S009:006 S010:018 S011:095 S012:050 S018:000 S025:005 S026:000 S030:000
S033:003 S042:002 S043:015 S045:098 S047:030 S066:010 S067:042 S069:060
S076:080 S077:010 S105:030 S110:004 S126:061
&Z0 =
&Z1 =
&Z2 = &Z3 =
&Z4 = &Z5 =
&Z6 = &Z7 =
&Z8 = &Z9 =
Last dialled = T2
+MS: 12,1,300,56000,1,0
Access Security: OFF Security Database, Security Mode & Call-Log Erase: FREE
Stored Phone Numbers: DISPLAYED OutDial: ENABLED
Caller ID: DISABLED
DES: 64bit
Internal Storage (#MEM): Enabled when DTR off: 4 Voice Messages
#ALM1=0,
#ALM2=0, PIN number =1234