Holtek BC66F5652 Manual Download Page 78

Page: 78 / 242

Rev. 1.10

October 23, 2020

Rev. 1.10

October 23, 2020

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

• RSTFC Register

Bit

Name

—

RSTF

LVRF

LRF

WRF

R/W

—

R/W

POR

—

“x”: unknown

Bit 7~4

Unimplemented, read as “0”

Bit 3

RSTF

: Reset control register software reset flag

Refer to the Internal Reset Control section.

Bit 2

LVRF

: LVR function reset flag

0: Not occur

1: Occurred

This bit is set high when a specific Low Voltage Reset situation condition occurs. This

bit can only be cleared to zero by the application program.

Bit 1

LRF

: LVR control register software reset flag

0: Not occur

1: Occurred

This bit is set high

if the LVRC register contains any non-defined LVR voltage register

values. This in effect acts like a software-reset function. This bit can only be cleared to

zero by the application program.

Bit 0

WRF

: WDT control register software reset flag

Refer to the Watchdog Timer Control Register section.

IAP Reset

When a specific value of “55H” is written into the FC1 register, a reset signal will be generated to

reset the whole device. Refer to the In Application Programming section for more associated details.

Watchdog Time-out Reset during Normal Operation

The Watchdog time-out Reset during normal operation is the same as the LVR Reset except that the

Watchdog time-out flag TO will be set to “1”.

WDT Time-out

Internal Reset

RSTD

WDT Time-out Reset during Normal Operation Timing Chart

Watchdog Time-out Reset during SLEEP or IDLE Mode

The Watchdog time-out Reset during SLEEP or IDLE Mode is a little different from other kinds

of reset. Most of the conditions remain unchanged except that the Program Counter and the Stack

Pointer will be cleared to “0” and the TO flag and PDF flags will be set to “1”. Refer to the System

Start Up Time Characteristics for t

SST

details.

WDT Time-out

Internal Reset

SST

WDT Time-out Reset during SLEEP or IDLE Mode Timing Chart

Summary of Contents for BC66F5652



















































































































































































































































Search results

Summary of Contents for BC66F5652

Reviews:

Related manuals for BC66F5652

Brands by name

Popular brands

Holtek BC66F5652, Manual

Search results

Summary of Contents for BC66F5652

Reviews:

Related manuals for BC66F5652

Brands by name

Popular brands