Holtek BC66F5652 Manual Download Page 149 | Manualshive

Page: 149 / 242

background image

Rev. 1.10

148

October 23, 2020

Rev. 1.10

149

October 23, 2020

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

SPI Bus Enable/Disable

To enable the SPI bus, set CSEN=1 and SCS=0, then wait for data to be written into the SIMD

(TXRX buffer) register. For the Master Mode, after data has been written to the SIMD (TXRX

buffer) register, then transmission or reception will start automatically. When all the data has been

transferred, the TRF bit should be set. For the Slave Mode, when clock pulses are received on SCK,

data in the TXRX buffer will be shifted out or data on SDI will be shifted in.

When the SPI bus is disabled, SCK, SDI, SDO and SCS can become I/O pins or other pin-shared

functions using the corresponding control bits.

SPI Operation Steps

All communication is carried out using the 4-line interface for either Master or Slave Mode.
The CSEN bit in the SIMC2 register controls the overall function of the SPI interface. Setting this

bit high will enable the SPI interface by allowing the SCS line to be active, which can then be used

to control the SPI interface. If the CSEN bit is low, the SPI interface will be disabled and the SCS

line will

be in a floating condition

and can therefore not be used for control of the SPI interface.

If the CSEN bit and the SIMEN bit in the SIMC0 are set high, this will place the SDI line in a

floating condition and the SDO line high. If in Master Mode the SCK line will be either high or low

depending upon the clock polarity selection bit CKPOLB in the SIMC2 register. If in Slave Mode

the SCK line will be in a floating condition. If the SIMEN bit is low, then the bus will be disabled

and SCS, SDI, SDO and SCK will all become I/O pins or the other functions. In the Master Mode

the Master will always generate the clock signal. The clock and data transmission will be initiated

after data has been written into the SIMD register. In the Slave Mode, the clock signal will be

received from an external master device for both data transmission and reception. The following

sequences show the order to be followed for data transfer in both Master and Slave Mode.

Master Mode

• Step 1

Select the SPI Master mode and clock source using the SIM2~SIM0 bits in the SIMC0 control

register.

• Step 2

Setup the CSEN bit and setup the MLS bit to choose if the data is MSB or LSB first, this setting

must be the same with the Slave devices.

• Step 3

Setup the SIMEN bit in the SIMC0 control register to enable the SPI interface.

• Step 4

For write operations: write the data to the SIMD register, which will actually place the data into

the TXRX buffer. Then use the SCK and

SCS lines to output the data. After this, go to step5.

For read operations: the data transferred in on the SDI line will be stored in the TXRX buffer

until all the data has been received at which point it will be latched into the SIMD register.

• Step 5

Check the WCOL bit if set high then a collision error has occurred so return to step 4. If equal to

zero then go to the following step.

• Step 6

Check the TRF bit or wait for a SPI serial bus interrupt.

• Step 7

Read data from the SIMD register.

• Step 8

Clear TRF.

• Step 9

Go to step 4.

«
...
147
148
149
150
151
...
»

Summary of Contents for BC66F5652



















































































































































































































































Reviews:

No comments

Related manuals for BC66F5652

Brand: Panasonic Pages: 2

Brand: Javad Pages: 10

Brand: Javad Pages: 7

Brand: Javad Pages: 4

Brand: Salora Pages: 7

Brand: Samson Pages: 92

Omni Pager OP1097-2

Brand: Silent Call Communications Pages: 2

Brand: Aiwa Pages: 20

Brand: Zaxcom Pages: 30

Brand: Conrad Pages: 49

Brand: EasyGates Pages: 6

Brand: Easy wave Pages: 4

AIR-EAGLE FM2 43-1000-SSB-R1/8-DC

Brand: BWI Eagle Pages: 2

Brand: Endress+Hauser Pages: 26

Brand: Aluprof Pages: 4

Brand: American Fibertek Pages: 4

Digital-Satellite-Receiver

Brand: Dolby Laboratories Pages: 66

Brand: Skytec Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands