Hitachi HVM Navigator V03-06 User Manual Download Page 4

Page: 4 / 312

Contents

HVM Navigator User's Guide - Migration

Procedure for Concurrent Maintenance mode .............................................. 3-28

Checking if Concurrent Maintenance mode finished normally ........................ 3-43

Recovering LPAR ........................................................................................ 3-45

Rolling back WWNs .................................................................................... 3-51

Policy migration ................................................................................................ 3-56

Procedure to create migration policy ........................................................... 3-57

Procedure to execute Policy migration ......................................................... 3-62

Procedure to interrupt Policy migration ........................................................ 3-66

Procedure to edit Policy migration ............................................................... 3-67

Return migration .............................................................................................. 3-74

Exchanging or updating hardware or software .................................................... 3-74

Saving and backing up HVM configuration .......................................................... 3-75

Saving HVM configuration ........................................................................... 3-75

Backing up HVM configuration .................................................................... 3-77

Registering/removing migration WWN ................................................................ 3-80

Flow to register/remove migration WWN ..................................................... 3-81

Prerequisite Setting .................................................................................... 3-82

Registering migration WWN to host group ................................................... 3-96

Removing migration WWN from host group ................................................. 3-98

Giving migration WWN a nickname ........................................................... 3-100

Exporting CSV file .................................................................................... 3-104

Adding storage device .............................................................................. 3-106

Commands for Storage Navigator Modular 2 CLI executed from HVM Navigator3-113

Other functions and settings ................................................................... 4-1

Functions and settings for Shutdown and Concurrent Maintenance modes ............. 4-2

Checking applicable conditions before migration execution ............................. 4-2

Specifying LAN port (IP address) for management server ............................... 4-4

Tracing back Migration History on LPARs ....................................................... 4-5

Functions and settings for Shutdown mode .......................................................... 4-7

Automatic shutdown of source LPAR ............................................................. 4-7

Automatic shutdown setup ........................................................................... 4-8

Changing setting of CPU, memory and service ratio on destination ............... 4-10

Functions and settings for Concurrent Maintenance mode ................................... 4-11

Executing Rehearsal ................................................................................... 4-11

Executing Connectivity Test ........................................................................ 4-14

Extending timeout period for LPAR migration in Concurrent Maintenance mode4-17

Canceling LPAR migration ........................................................................... 4-19

Monitoring memory transfer ....................................................................... 4-21

Usage notes .......................................................................................... 5-1

Backing up and restoring HVM configuration ........................................................ 5-5

Backing up HVM configuration ...................................................................... 5-5

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Search results

Summary of Contents for HVM Navigator V03-06

Reviews:

Hitachi HVM Navigator V03-06, User Manual, Page: 4 / 312

Search results

Summary of Contents for HVM Navigator V03-06

Reviews: